-40%

HX-SXPWM-A AC90V-260V Input DC90V Output 8A PWM DC Motor Speed Controller Driver

$ 25.64

Availability: 16 in stock
  • Condition: New
  • Model: DC Motor Speed Controller
  • MPN: HX-SXPWM-A-DC90V
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Item must be returned within: 30 Days
  • Country/Region of Manufacture: China
  • Brand: Unbranded/Generic
  • Return shipping will be paid by: Buyer
  • All returns accepted: Returns Accepted

    Description

    HX-SXPWM-A AC90V-260V Input DC90V Output 8A PWM DC Motor Speed Controller Driver
    Note:
    1.
    This product is a DC motor speed controller,Only for DC motor speed control,(Can be customized DC 48V/110v/180v/220v Output)
    2. Please confirm that the rated current of your motor is less than 5A before ordering.Thanks!~
    Working Environment:
    1
    .
    ambient air temperature: -10 ~ 40 ° C
    2
    .
    the air relative humidity of 85% or less, well-ventilated
    3
    .
    installed in a well-ventilated, no severe impact, no vibration, no explosion hazardous media and no conductive metal powder occasions.
    Features:
    1
    .
    the input power (VAC): AC90-260V 50/60 Hz (Wide voltage range)
    2
    .
    the output armature voltage range (VDC): 0-90V/110V/180V/220V (can be customized different versions)
    3
    .
    the output armature current range (A): 8A (0.1A-10A can be arbitrarily set) If the current is too large need to increase the heat
    4
    .
    the output excitation voltage range (VDC): 100V/200V (default full bridge rectifier, which is 0.9 times the input voltage)
    5
    .
    the output excitation current range (A): 1A
    6
    .
    the operating frequency: 16 KHz
    7
    .
    the given signal mode (V / mA): the default potentiometer, 0-5V, 0-10V, 4-20mA, PWM, button type
    8
    .
    enable control mode (EN): switch
    9
    .
    soft start (acceleration time adjustment range) (S): 0-10S (default3 seconds)
    10
    .
    soft stop (deceleration time adjustment range) (S): 0-10S (default 3 seconds)
    11
    .
    double closed-loop PI regulation, (voltage, current) control more reliable
    12
    .
    IR torque compensation range: 0-100% (default 0)
    13
    .
    over-current protection range: 0-set value (default 8A)
    14
    .
    over-current protection: stop the output and instructions (display code E1)
    15
    .
    short-circuit protection: stop the output and instructions (display code E0)
    16
    .
    overheating protection: power tube temperature exceeds 100 ° turn off the output and instructions (display code E2)
    17
    .
    built-in digital display module, can display real-time operating voltage and current
    18
    .
    Dimensions: length 159mm × width 98mm × height 38mm
    19
    .
    wiring: terminal type (convenient)
    1
    .
    the use of pulse width technology to make the speed more stable, low-speed efforts
    2
    .
    with short circuit, over current, over-temperature protection cut-off device to make the performance more reliable
    3
    .
    with soft-start device to eliminate the motor starting current is too large
    4
    .
    high and low voltage signal completely isolated, the use of more secure
    Precautions:
    1
    .
    the governor to close the input power, the hands of a minute to prohibit high-pressure touch terminals, there are high-voltage capacitors to prevent electric shock!
    2
    .
    for the two lines of the DC permanent magnet motor, two leads directly to the armature M + with M-. Prohibited access excitation!
    Instruction manual
    PWM signal requirements:
    1. the default PWM signal level is 5V, the signal frequency 1KHZ above, with a load capacity of more than 0.5MA.
    2
    .
    5V level without string resistance Input at PWM port,
    10V level PWM input from 0-10V port or string 10K resistor at PWM port input,
    12V level string 3.9K resistor from 0-10V port input or string 13.7K resistor In the PWM port input,
    24V level string 16.8K resistor from 0-10V port input or string 27K resistor in the PWM port input.
    Package:
    1pc HX-SXPWM-A AC90V-260V Input DC90V Output 8A DC Motor Speed Controller Driver
    Package
    1pc HX-SXPWM-A AC90V-260V Input DC90V Output 8A DC Motor Speed Controller Driver

    Payment Details
    We only accept Paypal Payment.
    We will send the item to you as soon as you won and paid.
    Delivery Details
    We provide standard shipping to international via China Post airmail or Hongkong Post airmail with tracking number.Contact us if not receive items.
    We only ship to the approved address given in Paypal Payment.Please make sure payment address in Paypal is correct.Any non-received items caused by invalid address registered on Paypal are not in our full refund or replacement policy.
    Returns and Replacements
    We accept returns and replacements within 30 days from the day the cutomer receive the products.Please make first contact within 30 days from receiving the order.Products should be returned in original condition.
    About Feedback
    We will try our best to solve any dispute and satisfy our customers.
    Please contact us firstly if you have any problems.As you know,a negative feedback can deal nothing and the positive feedback is very important for us.So we hope to your understanding.And we will appreciate if  you would like to contact us for solving your problems.Thanks!