Heat Dissipation PWM 4 Wire Fan Temperature 2-Way Speed Controller Board Module

Description

Visit store
Items for sale
About us
Product Details
Note: This is a four-wire PWM fan controller can only control in line with Intel standard four-wire fan fan (12-48V majority of four-wire fan support), can not control the 2-3 line fan, can not be completely shut off fan.
Although the controller can work between 8-60V, the actual power supply voltage must match the fan operating voltage. For example, to control the 12V fan, it must be powered by 12V. The wrong selection of the power supply may burn the fan and damage the control panel at the same time! !
Features:
1. DC8-60V wide operating voltage range (in this case is the control panel can work in this voltage range, the actual work of the controller power supply and fan are together, it is necessary to fan power supply in accordance with the requirements, otherwise it will damage the fan) .
2. Dual independent thermostat, turn temperature display two channels (-9.9 ℃ to 70.1 ℃, error <1 ℃) and Fan Speed (resolution 10rpm, maximum display 999 * 10rpm, always displayed after more than 999).
3. The minimum speed fan and thermostat temperature zone through the key settings, flexible control, large setting range, saved setup process.
The switch can be set to stall alarm function (external AC buzzer sounding, off by default).
Specifications:
1.Operating voltage: DC8-60V (must be equal to the fan voltage, 12V fan, but if you use 24V power supply fan will burn)
2.Current: Dashboard Working current 35mA (12V) 22mA (24V)
3.Control: not fan the current limit, but the board fan connector pins do not exceed 4.the maximum 3A current, use more current fan set the fan power cable is connected directly to the mains!
5.Control Output range: 10% -100% (this is the signal output range, the situation depends on the fan performance)
6.Temperature Probe Specifications: NTC 10K B = 3950
7.Temperature measurement: -9.9 ℃ to 70.1 ℃ error <1 ℃ (use 1% precision probe)
8.Temperature range temperature zone: accelerating temperature 0-60 ℃, full temperature 10-70 ℃
9.Speed measurement: 10-9990 rpm, more than is always displayed maximum resolution of 10 rpm, display units * 10 rpm (speed measurement according to the most common 2-pole signal fan design, the vast majority of fans are 2 pole signal)
10.Stall warning speed: less than 375rpm
Wiring instructions:
Blue screw terminal connections the mains (power supply voltage equivalent to the fan voltage use, and in the 8-60V range), please note not to take the wrong polarity; "Channel 1" and "Channel 2" two 4P socket connection fan, power supply line sequence is negative, positive power, speed feedback, PWM control (for details, see wiring diagram below); "thermal 1" and "2 thermal" Connect NTC thermistor (parameter 10K B = 3950) , respectively, with two channels of temperature control temperature fan; "beep" jacks AC buzzer, when you turn the alarm stops, the fan will stop the buzzer sounding.
Wiring Note:
The maximum allowable current single fan interface is 3A, if you need to control the higher current fan, set the fan power cord directly connected to the main power supply of the above (and fan controller capability independent of current, but to consider the power conductors current capacity)
Display Description:
Dashboard via digital display value, the right of the four LED digital tube digital tube current value indicates the meaning of the first line of each table led two temperature channels and a rotational speed (x10rpm), the two led the second line of distinguished representatives channel two of temperature and speed (x10rpm). Under normal operating conditions will follow the order of the four values ??displayed in turn, may at any time by pressing the "+" "-" button to quickly switch to manual values ??manually switch will stay at this value for a long time re-entering the round was state . It can be masked as required channel II display.
Setting Description:
1.Basic speed settings: basic speed setting for the fan speed to adjust the thermostat before start, which is lower than the temperature of the fan speed during acceleration. Setting method, press the "OK" button in any operating state, then a transverse channel at the same time the two led lights, digital display of the current setpoint (10-100), through the "+" "- "buttons to set the size, press the keys in rapid succession can modify, set up after pressing the" OK "button, enter the channel base two speed settings, press using the same method again after setting the" OK "button to save and exit .
2.Thermostat temperature zone and stall alarm settings: Under normal operating state, press "OK" button until the display L ** (** is a number) after the key is released, the two led a transverse channel simultaneously lit, on behalf of now in an accelerated temperature setting state channel, through the "+" "-" button to set this value (range 0-60, unit degrees Celsius); pressing After setting at "OK" button, a full-speed into the channel temperature set state, the display setting amount (range 10-65, in degrees C) for the "H **", in the same way; After setting press the "OK" button to enter the channel a stall alarm settings, "+" "- "button to set," boF "on behalf of this channel is closed stall alarm," bon "on behalf of this channel open stall alarm; After setting pressing the" OK "button to enter the channel number set two, order, and set the way ...... a same channel. When all the settings are finished, press the "OK" button to exit and save the parameters.
3.Channel II shows the mask setting: In the control panel power-off state, press and hold the "OK" button and hold down state is energized, digital display "2on" (open channel II display) or "2oF" (shield channel Second show), release "OK" button, the "+" "-" buttons to set the switch shield, pressed again after setting the "OK" button to exit into the normal working condition.
Setting Note:
1.Under setting state. Speed ??and temperature zones, if more than 15 seconds is not operated, the automatic exit without saving the data.
2.When the set temperature zone, full temperature must be higher than the same channel accelerated temperature of at least 5 degrees Celsius, a temperature value when setting causes this condition is not met, the controller will automatically adjust the temperature data to ensure compliance with the other difference is not low in conditions of 5 degrees Celsius, this is automatically adjusted to a one-way, and if you need to manually adjust the callback another temperature.
3.Channel two masked display settings only affect working state data show that two of the control channel and parameter settings are not affected, the normal work.
Package Included:
1x 4-Wire Temperature Control PWM Computer Fan Speed Controller
2x 1 meter temperature probe
1x Diameter 12mm length 10cm buzzer
Payment Method
Shipping Policy
Returns & Refund Policy
Feedback
Payment Method
EBAY Managed Payment.
But we only
Accept
your
Ebay Address
, please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping Policy
1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
Returns & Refund Policy
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.