DC Motor Over Current Protection Device Current Limit Switch 6V 12V 24V 5A

Description

Store category
Sign Up Now !
You may also like
DC Motor Over Current Protection Device Current Limit Switch 6V 12V 24V 5A
Product Description
Feature
:
DC Overload Protector used for overcurrent protection, short circuit protection, motor blocked protection, auto-stop overload protection.
The input voltage is DC 6V-28V.
Output current: 8A max (resistance load); 5A max (motor load)
The Protected Delay Time: 0-20s
The Current Limitation: 0.2A-10A
The Reset Time: 1-600s (automatic mode)
Include Power-on LED and current-limit-protected alarm LED.
Operating instruction:
Before you attempting to wire the protector, make sure power is off.
WARNING: DO NOT REVERSE POSITIVE AND NEGATIVE POWER LOADS.THIS WILL DAMAGE THE CONTROLLER.
1. Connect wires refer to the "wiring diagram" (NO. n picture).
2. Install the jumper to"Auto" or "Manual" modes. (Default is automatic mode.)
3. Set parameters of Current Limitation, Delay Time and Reset Time (automatic mode).
4. Turn on the power.
Current Limit Adjustment:
When the red alarm LED is lighting, eliminate the overcurrent factors, it will automatic reset (automatic mode), or push the Reset Button, reset the power (Manual Mode).
Reset the current limitation pot should as follow:
1. Turn off the power.
2. Adjust the Current Limitation pot until the desired maximum current is reached.
3. Reset the power.
Package Including:
1 x DC Current Overload Protector
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
1.We accept paypal payment and only ship to the address on paypal payment (Gift address is OK!)
2.Payment via PayPal should be made within 7-15 business days after auction close. Otherwise, we will relist the item and report an Unpaid strike.
Delivery details
1.
95% percent of our item shipment have track number
, Item reach most countries within 7-30 days. (Actual transit time may vary and is best estimated but not guaran- teed.)
2.
Please make sure your shipping
Address is Correct
. And
it is best to leave your
phone number
(pay attention,it is important).
3.
If you can't get the post after 30 days from the day we sent to you , please contact us directly . We would be with you to resolve the case. Please trust us, we will provide best service with honest attitude.
4.
We wll check each item clearly before we sent it out.
We promise each item would be shipped, but sometimes less than 0.5% packages might be lost in the way, you could choose to let us send another same item again or ask for money back.
5.
If you want ship ship by express,such as EMS, UPS, DHL, Fedex ,please contact us ,we will let you know the fee.
Terms of sales
From:xinxinjz
About us
1.If you have any question or problem about the item, you can contact us, We will response you within 24 hours;We pride ourselves on the best customer service possible, which is evident of our current eBay feedback rating. We look forward to serving you.
Contact us
If you have any question or problem about the item, please send message to us  .we will handle.
Feature: DC Overload Protector used for overcurrent protection, short circuit protection, motor blocked protection, auto-stop overload protection. The input voltage is DC 6V-28V. Output current: 8A max (resistance load); 5A max (motor load) The Protected Delay Time: 0-20s The Current Limitation: 0.2A-10A The Reset Time: 1-600s (automatic mode) Include Power-on LED and current-limit-protected alarm LED. Operating instruction: Before you attempting to wire the protector, make sure power is off. WARNING: DO NOT REVERSE POSITIVE AND NEGATIVE POWER LOADS.THIS WILL DAMAGE THE CONTROLLER. 1. Connect wires refer to the "wiring diagram" (NO. n picture). 2. Install the jumper to"Auto" or "Manual" modes. (Default is automatic mode.) 3. Set parameters of Current Limitation, Delay Time and Reset Time (