DC 5-32V Stepper Motor Speed Controller Driver Servo PLC Control For Industrial

Description

DC 5-32V Stepper Motor Speed Controller Driver Servo PLC Control For Industrial
Description
:
DKC-1A is an economical step
ping
motor controller. It uses an imported and high speed intelligent chip, it is applicable to all kinds
of harsh environment in any factory site. At the same time, some functions are added to make the controller more practical and convenient,
which is suitable for the round-trip motion control, limited function control, speed control and the like of sensors
Parameters
1. Voltage Input: DC5V - 32V
2. Multiple Protection Functions: anti-connection protection, over-voltage protection, over-current protection
3
.
Speed Regulation Performance: intelligent and automatic switch between on-board speed regulation and external speed regulation
4
.
Acceleration and Deceleration: used S- acceleration
,
with function of immediate stopping
5
.
Output Frequency: up to 20KHz
6
.
Input and Output: all input is optocoupler isolation, while output the negative pulse. The low level signal is valid
Function Setting
Operation mode: (dip switch, 1-up, 0-dow
n)
Automatic Round-trip Mode
Single Trigger Mode
Single Round Trip Mode
Jog Mode
S
1
0
0
1
1
S
2
0
1
0
1
NOTE:
1
.
The control signal is 0-24V
.
The signal is valid at the falling edge
.
The trigger signal must be over 2.5US.
2
.
The on-board potentiometer and the external potentiometer are automatically switched. If the interface of the external potentiometer is suspended, the on-board
potentiometer will regulate the speed. If the external potentiometer (less than or equal to 10K) is connected, the control board will automatically switch to the external
potentiometer to adjust the speed.
3
.
Operation setting switch and the on-board speed-regulating potentiometer are inside the controller, please open the case to set
them
.
Functions:
Automatic Round-Trip Mode:
After the controller is triggered and started, (COM and K4 connected), the motor will automatically move back and forth between the FWD limit and the REV limit until the input of the trigger is stopped.
Single Trigger Mode:
After the controller is triggered and started, the motor is in forward rotation until
it
touches the FWD limit
to
stop. It will be in reversal rotation if the controller is triggered and started again and will stop when it touches the REV limit. Start the motor and it will be in forward rotation again on and on.
Single Round Trip Mode:
After the controller is triggered and started, the motor is in forward rotation until
it t
ouches the FWD limit
to
stop. Then it automatically starts to reverse and won’t stop until it touches the REV limit.
Jog Mode:
When COM and K4 connected
,
the motor will be in forward rotation. When COM and K4
are
disconnected
,
the motor will stop
.
When COM and K3
are
connected
,
the motor will be in reversal rotation. When COM and K3 disconnected
,
the motor will stop
Package Included:
1 * DCK-1A Stepper motor controller (with manual)
Terms and Conditions :
Shipping
Shipping to most other countries takes about 10-30 days via Economy Int'l Airmail without tracking#. In rare case, it can take up to 40 days.
It depends on your location and local postal service(e.g., Russian Postal service is slow),
as well as the weather condition along the shipping.
Please verify your primary shipping address. We are not responsible for any wrong or undeliverable addresses
.
Payment
We accept payment via Paypal.
The buyer is responsible for any applicable import duties and local taxes.
Usually there's no any charges for small parcel. But please verify with your customs before making your purchase.
Contact Us
We take full responsibility if you receive wrong item or damaged item or item not as describled.
If you're not satisfied for any reason, please feel free to contact us. Just send us an message or email.
You can always get our solution pretty soon in our working time.
Your satisfaction is guaranteed.
About UG
Thank you for choose UG.
As a manufacturer of electronic module, UG have been in business more than 20 years, and therefor have wide experience in all the line we handle.
OEM Service Also Welcome!